Home
My Puzzles
FAQ
Report bug
Collected Puzzles
User listed puzzles
Random Puzzle
Log In/Out

HVAC/R Crossword Puzzle

Buddy Burns

1                
 
2                         3 4
     
5                     6          
   
  7                  
8    
9                     10        
     
  11                  
  12    
  13   14 15 16
      17              
           
18              
     
19                     20
     
21       22              

Across
1.Heat exchanger where the system heat is rejected and the refrigerant condenses into a liquid. The condenser is where hot pressurized refrigerant vapors in the compressor are cooled and liquefied by cooling tower water circulating through the tubes of the condenser. The condenser side is commonly referred to as the open recirculation system or open loop.
2.Any foreign object or substance not normally found in a specific location.
5.Measures and evaluates temperature.
6.A space partially exhausted by artificial means (i.e., suction measured in inches of Hg in a low pressure chiller).
7.Liquid refrigerant cooled below the condensing temperature of the refrigerant.
9.The process a liquid goes through to change phase from a liquid to a vapor.
10.An instrument or device for measuring, indicating or comparing a physical characteristic, i.e., temperature or pressure.
11.A mechanical device where the refrigerant is compressed from a lower pressure and lower temperature to a higher pressure and higher temperature. The compressor maintains a low pressure in the evaporator by continually removing refrigerant vapors. This low pressure, low temperature vapor is then compressed into a higher pressurize, hot refrigerant vapor which leaves the compressor and travels to the condenser. The motor in the compressor is the main consumer of energy in the chiller system. The energy used by the compressor is dependent on the pressure increase. The head pressure divided by the suction pressure or the condenser pressure divided by the evaporator pressure expresses this. If the compressor operates out of its original design, it will effect the energy consumption.
17.Used to remove foreign material from the water flow. The mesh size determines the size of the material/debris being removed.
18.The practical meter-kilogram-second unit of electric current that is equivalent to a flow of one coulomb per second or to the steady current produced by one volt applied across a resistance of one ohm.
19.Degree of hotness or coldness of an object or location measured on a definite scale.
21.When energy is added to an object or location, the motion of the molecules increases causing them to collide more frequently. The motion energy is converted into heat during the collisions. As more collisions occur more heat is released and the temperature of the object or location increases.
22.A retrofit is a modification to a chiller system. For example, a new style compressor replacing an older, less efficient style or to use a different refrigerant to comply with new standards. The results can affect energy efficiency.
Down
1.The process a vapor goes through to change phase from vapor to a liquid.
3.Heat exchanger where the system heat is absorbed and the refrigerant evaporates into a gas. By continually pulling refrigerant vapor out of the evaporator headspace, low pressure can be maintained causing the refrigerant to evaporate rapidly. Evaporation cools the refrigerant. This cold refrigerant produces chilled water by heat transfer. The evaporator side is commonly referred to as the closed loop system (chill water).
4.British thermal unit. The amount of heat required to raise the temperature of 1 pound of water 1 degree Fahrenheit.
8.Refrigerant
12.Is the temperature difference between the boiling point of the refrigerant in the evaporator and the actual temperature of the refrigerant gas after the evaporator. It is the “extra” temperature (or temperature rise) the refrigerant picks up in the evaporator after it boils.
13.The design capacity of a pump’s ability to circulate fluid.
14.The application of force to something by something else in direct contact with it.
15.Used as the lubricant in the compressor system to lubricate and protect bearings, shaft, etc.
16.A seal is a tight and perfect closure (as against the passage of gas or water) or a device to prevent the passage or return of gas or air into a pipe or container.
20.Air Conditioning and Refrigeration Institute

Use the "Printable HTML" button to get a clean page, in either HTML or PDF, that you can use your browser's print button to print. This page won't have buttons or ads, just your puzzle. The PDF format allows the web site to know how large a printer page is, and the fonts are scaled to fill the page. The PDF takes awhile to generate. Don't panic!




Google
 
Web armoredpenguin.com

Copyright information Privacy information Contact us Blog